Kookiez
  • Blog
  • Instagram
  • Pinterest
  • Twitter
  • Etsy Shop
  • Blog
  • Instagram
  • Pinterest
  • Twitter
  • Etsy Shop

How to create a pillow cover with a zipper

6/17/2012

1 Comment

 
Today I want to show you how to create a pillow cover with a zipper. There are a lot of YouTube videos out there that more or less show you how to do this (there is a good instruction as well at prudentbaby.com) but I always had the feeling that 'something' was missing. So after many attempts, and unfortunately also many mistakes, I now have the hang of it, and would like to share my experience with you. I actually find this way of working quite simple, and you can create your own pillow cover, WITH zipper, in 30 minutes or less! Advice: Before you start read the entire tutorial, so you get an idea where we are heading.
What do you need:
Fabric
Zipper
Ripper
Foto
You need two equal parts of fabric, e.g. 32 by 52 cm. Make sure to add room to create seams on all sides later. In this case I have added 2 centimeters on all sides. This means the actual pillow case will measure 30 by 50 cm.
Next you need a normal zipper, see a picture below.
Foto
First both parts of the fabric need to be pinned together, see below.
Foto
The line on top in purple has three different parts: A - B - A.
Foto
Both parts A measures approximately 5 cm. Sew both parts A in stitch length 3. Part B forms the middle of the purple line, and needs to be sewn in a larger stitch length e.g. 4,5. (Part B needs to be opened up by a ripper after the zipper has been added. This is easier if you use a larger stitch length). Make sure to leave a small space between part A and B (see break in purple line in picture above). By having a space between part A and B it is easier to track back where part B begins and ends, and use your ripper later on. After sewing parts A, B and A via the purple line, the outer and inner side of the pillow case look like this.
Foto
The seam on the inner side is flattened by ironing it, creating the following:
Foto
Make sure to indicate on the left and right side where your part A starts, as the gap might not be clearly visible anymore due to ironing. See the small purple line in the 3rd picture above. Now the zipper will be added.
Foto
Place the zipper exactly in the middle of the seam face down on the inner side.
Foto
When pinning the zipper to the seam check regularly to see that the zip is in the middle.
Foto
After the zipper has been pinned to the seam, you can sew it using a zipperfoot.
Foto
A zipper foot looks like this. The right side will be placed against the zipper, and will follow the zipper nicely when sewing. 
Foto
Start at the end of the zipper and work your way to the front (part where you can open the zipper).
Foto
When you are almost at the end of your zipper, leave the needle in the fabric and lift your zipperfoot. Now push the zip behind the zipperfoot. This might take some effort, but will always work. When the zip is past the zipfoot you can drop the foot again on the zipper/fabric.
Foto
Continue towards the end of the zipper. Turn, and continue on the other side. Make sure to make your turn beyond the start of part A, indicated earlier by a purple line (within the 5 cm range of part A).
Foto
When you meet the zip again, perform the same trick as earlier to push the zip beyond the zipfoot. Then continue along the zipper towards the end. Turn at the same point where you started and finish off.
Foto
The outer side of your fabric should now look like this.
Foto
You can use your ripper to open up part B, and your zipper is visible!
Foto
Turn the fabric inside out and pin the other three sides together. Leave the zipper open otherwise you cannot turn the fabric to the right side once sewn together. Sew all three sides together.
Foto
Cut the corners from the pillow to get really sharp corners after turning inside out. Make sure not to cut your thread, otherwise you get a hole in your work. Your pillow cover is now finished!
Foto
Tadaa there is your pillow cover!
Foto
Now you know how to make a pillow cover, you can make more!
Foto
Lots more!
Foto
Fabric used in this tutorial is from IKEA.
Enjoy making your own pillow covers!
1 Comment
Sphinx rug link
9/3/2013 06:13:17 pm

After a long time I got something fresh and quality content on related topic. I searched a lot for the related material but got almost replica work. Keep it up! It is really very informative.

Reply



Leave a Reply.

    ABOUT

    This is Kookiez. My blog on creative projects I am working on. I love to crochet, sew and knit.  And in the summer I also paint occasionally.
    I live in Rotterdam, Netherlands, and you can find me on Twitter via @KookiezNL or on Instagram via Kookieznl

    Subscribe

    RSS Feed

    INSTAGRAM

    Archives

    May 2015
    June 2014
    May 2014
    March 2014
    August 2013
    July 2013
    May 2013
    April 2013
    September 2012
    July 2012
    June 2012
    May 2012
    April 2012
    December 2011
    June 2011
    May 2011
    April 2011
    March 2011
    February 2011

    Twitter

    Tweets by @Kookieznl

    Categories

    All
    Blanket
    Buttons
    Cardigan
    Crochet
    Dress
    Fabric
    Fashion
    Jacket
    Kookiez
    Moulage
    Naaicafe
    Pattern
    Ribbon
    Rotterdam
    Sewing
    Summer
    Yarn

    SUBSCRIBE

    RSS Feed

Powered by Create your own unique website with customizable templates.